By NORMA Group

By NORMA Group

Home Drainage Center

1
Identify the Problem
2
Possible Solution
3
Installation / Where to Buy
Installation / Where to Buy
Water on Walkway (High): Installation Instructions

Prior to installation, have your local utility companies locate and mark the location of existing utilities.

Layout your drainage system and mark the location of trenches and individual parts to be installed with marking paint before digging. Carefully remove grass or plants that are located where the trench will be dug so they can be replanted after installation. Trenches should be dug such that they slope a minimum of 1% away from your house. Place all excavated dirt on a tarp so that it can be used later to backfill.

To speed up installation, a trenching machine can be used to dig all trenches, especially in areas with particularly hard soil. NDS drainage products have been designed to be installed in any soil type. Due to the variety of pipe types and sizes, double check that all pipe connection points are the correct size. Please follow all installation directions included with the individual parts of your drainage system. To create watertight connections between products, apply a bead of waterproof silicone to both parts and connect.

This system requires that the elevation of the Pop-Up Emitter be lower than the elevation of the area drain or the system will not drain.

  • Dig trench for EZ-Drain and Flo-Well. Flo-Well(s) should be installed under the areas where the runoff is collecting. 
  • Dry fit (no glue) the entire drainage system from the EZ-Drain to the Pop-Up Emitter. 
  • The Flo-Well should be installed at least 10’ away from any existing structure. 
  • Measure and cut all pipe to necessary lengths. 
  • After completing each step, glue parts together if a water tight connection is required.
     

TIP: If installing the drain in an existing concrete area, a wet concrete saw will be required to cut the concrete prior to installation.

  • Connect sections of EZ-Drain with internal corrugated couplers and place an end cap on the end that does not connect to the Flo-Well. 
  • Lay EZ-Drain pipe in the trench.
Connect EZ-Drain

  • Knock out the appropriate holes in the side panels of the Flo-Well where the EZ-Drain will be installed. 
  • Assemble the Flo-Well using the interlocking side panels. 
  • Slide the drain pipe through the hole in the Flo-Well side panels.
     

TIP: Lay the Flo-Well panels on bricks or other hard surfaces and use a hammer to knock out the holes in the side panels.

Flo-Well Dry Well and EZ-Drain

  • Knock out the center hole of the Flo-Well lid. 
  • Place the lid on the Flo-Well side panels then place the Flo-Well Surface Inlet onto the Flo-Well lid.

  • Using a Corrugated Pipe Adapter, connect the EZ-Drain to an elbow with a weep hole. The elbow should be installed with the weep hole on the horizontal side of the elbow. 
  • Slide the Pop-up Emitter onto the elbow. An additional length of pipe can be used to bring Pop-up emitter to the surface.
     

TIP: To avoid damaging your Pop-Up Emitter with your lawn mower, raise the cutting level of the blades or avoid passing the mower over the Pop-Up Emitter.

  • Backfill and replace any grass or plants that were removed.
     

TIP: DO NOT BACKFILL WITH SOIL WITH HIGH CLAY CONTENT.

Water must be able to easily pass through the backfilled soil.

Where to Get It

Where to Buy NDS Solutions

Find a Dealer or Distributor near you

NDS products are available at a variety of leading home & garden retailers and professional distributors.  Click below to find a store near you. 

Find a Contractor

Need More Help?

Find a Contractor

Enter your location and find professional drainage and irrigation contractors in your area that have completed NDS training and certification.

Need help? Ask Dr. Drainage

Have questions? Need help? Want to know more?

Find out how NDS solutions experts can help you solve your water management problems.